2014-2019 C7 Corvette Supercharger Kit LT1 V3 Si-Trim

2014-2019 C7 Corvette Stingray Supercharger Kit LT1 V3 Si-trim 4.0"

A&A Corvette produced the first C7 Corvette supercharger system in October of 2013. After much testing and a few “tweaks” here and there, production systems became available in January of 2014. Aesthetically as well as mechanically, we believe this to be the finest system available for the new C7 Stingray.

C7 Corvette Stingray A&A Supercharger

Take a close look and we’re sure you’ll agree!

Advantages of the A&A Supercharger system:

Proprietary supercharger units built specifically for A&A Corvette by Vortech Engineering are used exclusively. We have found Vortech to build the most efficient units available and to also offer us the best available customer service and support. Self- contained V3 Si head units are standard. The Si units are the most efficient model available in the 500 to 700 horsepower range. All our units are available in a highly polished or satin black finish.

We have larger units available, capable of well over 1000 horsepower for properly built engines.

A&A is the only manufacturer to include a fully machined SFI approved balancer with interchangeable lower pulleys as standard equipment. Others just use a simple pulley that bolts to the stock cast iron balance. Which would you trust?

This balanced design allows us to use a dedicated 8 rib belt that does not interfere with the water pump or alternator belt.

A&A continues as the leader in intercooler design with our new C7 Ram Air Intercooler. GM did a great job sealing in the radiator cavity from the grill opening to the radiator. This whole cavity is a high-pressure area when the vehicle is at speed. After carefully looking at all placement and airflow direction options, we came up with our present design. The intercooler lays flat and is hidden behind the bumper cover. We weld an aluminum scoop to the intercooler which protrudes into the incoming air stream and directs it through the intercooler and out the bottom. Any air that is grabbed by the scoop is literally rammed through the intercooler core. Simple physics won’t allow it to go anywhere else. Hence the name “Ram Air Intercooler”.

C7 Corvette Stingray A&A Supercharger

Others went with the flat placement but forgot all about directing airflow through the cooler. Laying the intercooler flat and putting a plastic air dam behind it just isn’t going to work efficiently. Not only are they asking the air to abruptly make a right angle turn, they’re also trying to get the air to flow from a low-pressure area (under the car) into a high-pressure area (inside the radiator cavity.) A&A wins this one hand down.

Our bracket design once again stands out from the crowd. Amazingly stiff while remaining simple, it really is a work of art. We have solid billet mounts that attach the main bracket to the block and the cylinder head. Our cylinder head mount has FOUR mounting points. Others use a simple spacer with one long bolt going through the middle. This can rotate under extreme forces. Ours simply cannot move in any direction.

C7 Covette Supercharger

Our bracket uses steel idler and tensioner pulleys with dual bearings and the proper stanchions to support the bearings.

Even better for the consumer is that our entire bracket, pulley, and supercharger assembly comes completely pre-assembled for you. Take it out of the box and bolt it onto the block and cylinder head without having to assemble a thing. Even the mounting bolts are “zip-tied” in the proper holes. It really is a 5-minute proposition to bolt the entire supercharger and bracket assembly on the engine.

Application: 2014, 2015, 2016, 2017, 2018, 2019 C7 Corvette

- SKU
  AAC7SCKIT-01
- Weight
  45 lbs
Configurator Products
No
Configurator Status
No
Covercraft Status
No
Disable loading on additional products
No
Disallow Use of Coupons
No
Select Featured
No
Finish
Black SI Trim, Polished SI Trim

There are no comments yet. Be the first to leave a comment

Shipping

We utilize UPS, Fedex, and USPS for all of our shipping needs. Carrier choice is based upon availability and needs of the customer and is the sole discretion of SouthernCarParts. We always try to ship within 24 hours of order placement (do to the custom nature of some products, shipping within 24 hours is impossible, actual shipping time frames will be listed in the product description). Please keep in mind that some products such as Custom Fit Car Covers, Lloyds Floor Mats, Painted accessories, and Racemesh Products can take 3 -10 days to ship and are charged at time of order placement. Racemesh products take 4 weeks to ship as they are made to order.

Returns

Should you need to return a part for refund, exchange, or credit, please contact our returns department within 30 days of purchase at orders@southerncarparts.com for a Return Merchandise Authorization (RMA) number. Most problems, such as installation, can be solved with a telephone call (888-631-1433). Southern Car Parts will not accept returned goods without prior authorization and an RMA# written clearly on the exterior of the box. The customer is responsible for freight on all return orders. Parts authorized to be returned, on a non-exchange basis, are subject to a 20% restocking fee. Returns will only be accepted within 30 days of the original date of shipment. Custom painted parts - Once these parts are started, we can refund you less the paint(chemicals) that have been used. Exception is rear spoilers and front splitters, we can refund less 20%.

Custom-made-to-order items are NOT returnable. This includes embroidered floor mats and car covers.
Damages in Shipping

All damages from shipping must be reported to Southern Car Parts within two business days from tracking number delivery confirmation. After two business days, damages become the responsibility of the customer.